Manufacturer: SOLVAY
Produced At: Import/ China
Product Category: IXEF PARA
Product No: Ixef 1032
Product Quantity: 25KG / BAG
Product Features: Chemical Resistant,Creep Resistant,Good Dimensional Stability,High Flow,High Strength,Low Moisture Absorption,Outstanding Surface Finish,Ultra High Stiffness
Ixef? 1032
Natural: Ixef? 1032/0008
Black: Ixef? 1032/9008
Custom Colorable
Filler / Reinforcement |
|
Features |
|
Uses |
|
RoHS Compliance |
|
Appearance |
|
Forms |
|
Processing Method |
|
Multi-Point Data |
|
Physical | Dry | Conditioned | Unit | Test Method |
Density | 1.77 | -- | g/cm3 | ISO 1183 |
Molding Shrinkage | 0.10 to 0.30 | -- | % | Internal Method |
Water Absorption (73°F, 24 hr) | 0.13 | -- | % | ISO 62 |
Moisture Absorption - Equil, 65% RH | 1.3 | -- | % | Internal Method |
Mechanical | Dry | Conditioned | Unit | Test Method |
Tensile Modulus | 3.48E+6 | 3.34E+6 | psi | ISO 527-2 |
Tensile Stress (Break) | 40600 | 36300 | psi | ISO 527-2 |
Tensile Strain (Break) | 1.8 | 2.0 | % | ISO 527-2 |
Flexural Modulus | 3.41E+6 | -- | psi | ISO 178 |
Flexural Stress | 58000 | -- | psi | ISO 178 |
Impact | Dry | Conditioned | Unit | Test Method |
Notched Izod Impact | 2.2 | -- | ft·lb/in | ASTM D256 |
Unnotched Izod Impact | 17 | -- | ft·lb/in | ASTM D256 |
Thermal | Dry | Conditioned | Unit | Test Method |
Heat Deflection Temperature (264 psi, Unannealed) | 446 | -- | °F | ISO 75-2/A |
CLTE - Flow | 8.0E-6 | -- | in/in/°F | ISO 11359-2 |
Electrical | Dry | Conditioned | Unit | Test Method |
Volume Resistivity | 1.0E+13 | -- | ohms·cm | IEC 60093 |
Electric Strength | 600 | -- | V/mil | IEC 60243-1 |
Dielectric Constant (110 Hz) | 4.50 | -- | IEC 60250 | |
Dissipation Factor (110 Hz) | 9.0E-3 | -- | IEC 60250 | |
Comparative Tracking Index | 600 | -- | V | IEC 60112 |
Flammability | Dry | Conditioned | Unit | Test Method |
Flame Rating 3 | HB | -- | UL 94 | |
Glow Wire Flammability Index | IEC 60695-2-12 | |||
0.031 in | 1430 | -- | °F | |
0.06 in | 1430 | -- | °F | |
0.12 in | 1760 | -- | °F | |
Glow Wire Ignition Temperature | IEC 60695-2-13 | |||
0.031 in | 1470 | -- | °F | |
0.06 in | 1470 | -- | °F | |
0.12 in | 1520 | -- | °F | |
Oxygen Index | 25 | -- | % | ISO 4589-2 |
Injection | Dry | Unit | |
Drying Temperature | 176 | °F | |
Drying Time | 12 | hr | |
Suggested Max Moisture | 0.30 | % | |
Rear Temperature | 482 to 500 | °F | |
Middle Temperature | 500 to 518 | °F | |
Front Temperature | 518 to 536 | °F | |
Nozzle Temperature | 500 to 554 | °F | |
Processing (Melt) Temp | 536 | °F | |
Mold Temperature | 248 to 284 | °F | |
Injection Pressure | 7250 to 21800 | psi | |
Injection Rate | Fast | ||
Holding Pressure | 10900 | psi | |
Back Pressure | 0.00 to 145 | psi | |
Screw L/D Ratio | 15.0:1.0 to 20.0:1.0 | ||
Injection Notes | |||
Injection time: 0.5 to 2.5 sec Holding time: 3e sec Cooling time: 2.5e2 sec (e= wall thickness in mm) Storage Ixef? compounds are shipped in moisture-resistant packages at moisture levels according to specifications. Sealed, undamaged bags should be preferably stored in a dry room at a maximum temperature of 50°C (122°F) and should be protected from possible damage. If only a portion of a package is used, the remaining material should be transferred into a sealable container. It is recommended that Ixef? resins be dried prior to molding following the recommendations found in this datasheet and/or in the Ixef? processing guide. Drying The material as supplied is ready for molding without drying. However, If the bags have been open for longer than 24 hours, the material needs to be dried. When using a desiccant air dryer with dew point of -28°C (-18°F) or lower, these guidelines can be followed: 0.5-1.5 hour at 120°C (248°F), 1-3 hours at 100°C (212°F), or 1-7 hours at 80°C (176°F). Injection Molding IXEF 1032 compound can be readily injection molded in most screw injection molding machines. A general purpose screw is recommended, with minimum back pressure. The measured melt temperature should be about 280°C (536°F), and the barrel temperatures should be around 250 to 260°C (482°F to 500°F) in the rear zone, gradually increasing to 260°C to 290°C (500°F to 554°F) in the front zone. If hot runners are used, they should be set to 250°C to 260°C (482°F to 500°F). To maximize crystallinity, the temperature of the mold cavity surface must be held between 120°C and 140°C (248°F and 284°F). Molding at lower temperatures will produce articles that may warp, have poor surface appearance, and have a greater tendency to creep. Set injection pressure to give rapid injection. Adjust holding pressure and hold time to maximize part weight. Transfer from injection to hold pressure at the screw position just before the part is completely filled (95%-99%). |
Products are widely used in plastic modification, automotive, construction, electrical and electronic, industrial, daily necessities and other fields